Step 1: Trim Your Beard
This should be done especially if you have long, full whiskers, or if it has been quite a while since you have shaved.
You can make it with a clipper or a pair of scissors, but most optimally, you can use an electric beard trimmer for the purpose.
Step 2: Wash Your Face
You can use a hot (read lukewarm) washcloth for the purpose. Its heat and moisture will aid to soften your beard and lift it.
Alternatively, you can take a hot shower. It will soften your beard and make it easier for you to shave.
You can also keep an exfoliating face wash handy.
Step3: Keep Your Shaving Kit Handy
Remember, you need to shave right after you wash your face.
You should not start shaving when the beard gets dry. In case you are using a disposable razor, you should soak it in some cold water.
Remember, hot water will simply expand the blade and make it duller.
Step 4: Apply Your Shaving Cream With A Shaving Brush
Even a quality shaving brush is very functional in softening your beard and skin exfoliation.
If you do not like using foam, gel or cream, you can also try some specialty shaving oil or conditioner.
Whatever you choose, do not use a soap bar. It can leave residue on the blade and make it dull.
Step 5: Be Careful About Choosing The Blade
You should choose your blade by judging the texture of your skin, the coarseness of your beard and your favored shaving method.
If you have long hair or very sensitive skin, then ideally, you can use a multiple-blade razor (2, 3, 4, and 5).
Step 6: Start Shaving
First, work on one side of your face and with light, short, descending strokes, work gradually towards another side.
As you engage one hand to use the razor or shaver(the best Braun Series 7 799cc wet dry shaver), you can use the free hand to pull your skin.
You should always keep the blade parallel to the face, and rinse it frequently so that it does not clog.
Continue the process until you have shaved your face entirely.
Step 7: Rinse Your Face
This should be done with lukewarm water. Having done that, run your fingers all over your face to see if you have missed any patches.
Carefully attend to the areas around your jawline and neck.
Step 8: Apply An After-Shave
After patting your skin dry with a clean towel, apply a refreshing and mild toner on your skin.
After that, apply a non-alcohol shaving balm. You can also use aloe and tea tree oil in moderate quantities.
However, tea tree oil can irritate freshly-shaved skin.
It is very important to moisturize your face as it can duplicate and strengthen the part played by your body’s naturally formed sebum, which is skin’s innate restorative liquid.
Step 9: If You Develop Nicks Or Small Cuts…
You can apply witch hazel to relieve the cuts. This can also prevent razor burn.
If bleeding persists, then apply small bits of moistened kitchen paper/toilet roll to the cuts.
You can also use a styptic pencil. Just dampen it and spread across the area where the scratch has happened.
Step 10: Take Care Of Your Shaving Kit
It is equally important to maintain the shaving implements after you have used them.
Make sure that you rinse the razor, as well as the brush after every use.
Shake the excess water that sticks on them, and store them in a dry place.
No sooner than you feel an uncomfortable pull/ tug on your beard, replace the blades.
Do not forget that a dull blade is likely to make your face feel sore and raw. This can lead to a serious razor burn.
A Bonus Suggestion on how to Shave a beard
The hair you have on the different parts of your face may not grow in the same direction.
You may also have placed on the neck where the hair grows in a circle. In such tricky places, you can shave with the grain at first.
It will help to avoid razor burn. Again, if you want a closer shave, you can lather up once again and go across or against it.
Hopefully, you have found some grand tips on how to shave beard in this article. So, are you ready to look ‘wow’ now?